summer limited time offer save up to 50% +free shipping

CAMAROPULSE™ USB Wireless Warning Anti-theft Light For Chevrolet Camaro

$35.99

This deal will end in

00m
:
00s

Emitting Color: Blue light

Add to cart
Buy now

**Enhance Security with USB Wireless Warning Anti-theft Light for Chevrolet Vehicles**

Ensure your Chevrolet Volt, Malibu, Camaro, Cobalt, Orlando, Spark, Colorado, Bolt, Onix, Traverse, or Blazer stays protected with the USB Wireless Warning Anti-theft Light. This innovative device provides an additional layer of security by deterring potential thieves and enhancing visibility in low-light conditions.

**Key Features:**

- **Wireless Installation:** Easy setup with USB power connection, no complex wiring needed.
  
- **Anti-theft Deterrent:** Flashing red LED light simulates a security system, discouraging unauthorized access to your vehicle.
  
- **Universal Compatibility:** Compatible with various Chevrolet models, including Volt, Malibu, Camaro, Cobalt, Orlando, Spark, Colorado, Bolt, Onix, Traverse, and Blazer.

- **Enhanced Visibility:** Provides a visible warning signal to deter theft and enhance your vehicle's visibility in dark environments.

- **Compact Design:** Sleek and discreet design blends seamlessly with your Chevrolet's exterior aesthetics.

Protect your Chevrolet with the USB Wireless Warning Anti-theft Light, a simple yet effective solution to enhance security and peace of mind wherever you go. Easy to install and universally compatible, it's the perfect addition to safeguard your vehicle against theft and unauthorized access.

Specifications:
 
This is Solar Powered Simulated Dummy Alarm Warning ,Anti-Theft Flashing Light  for protect  your property from potential thieves at night.
Important : It is a fake alarm light, not really alarm system.
 
Compatible Model:Universal
Material: ABS
Color: red, blue
Working voltage: 0.05V
Working current: 0.02A
Power: 0.01W
Size: 50*25*14mm
Power :Built-in high capacity Ni-mh battery,Solar charging,  USB charge supported.
Install:With self-adhesive sticker, can be easily installed on the car instrument panel, door side, car grille, bumper, as warning or decorative lights
Function: Built-in light sensor, this LED light will flash in nighttime and will not flash in daytime. (You can cover the other end by dark paper if you want it to flash in daytime.)
Flashing light :5 seconds/time.
Use: Car or others
 
Features: 
The light can discourage break-ins in nighttime.
Easy to install and looks clean on your dash panel.
Built-in light sensor, this LED light will flash in nighttime and will not flash in daytime.
This LED alarm light does NOT require a car alarm system.
No wires needed, just stick it to the roof of the vehicle with corresponding glue.
Solar energy can be absorbed and saved in high efficiency solar cells.Quick and fast charging with solar light
Do not need to install battery. It's powered by solar. It can blink for whole night after enough sun shining in daytime.
You need not put it under sunshine directly. Sunshine above the dashboard is enough.
It can be charged by solar whether you put switch to "on" or "off". Switch is tiny. You need a ballpen or little stick to push it.
 
Package content include: 1pc Simulated Dummy Alarm LED Light  
Only the above package content, other products are not included.
(Note:This item come without retail box,and we will pack well before shipping.)
 
Installation Method: 
  Easy to install,Clean the car surface, keep it dry, Easily Installation directly.No Need Drilling Required,no need of welding.
  Before installation, thoroughly clean the surface of installing position.make sure that the target area is clean, no oil.
  The double-sided adhesive tapes on its back enables it to be pasted directly .
 Please note that please use the heat gun to warm up the adhesive tape before installed, to make the item stick tightly
  You'd better heat the adhesive tape by hair dryer to Enhanced viscosity.
  Please note that please use the hair dryer to warm up, 
  the adhesive tape before installed, to make the item stick tightly. (No need too hot)
   How to use:
  1.Clean and dry the area where you want to install.
  2.Check the place.Tear off protective film of double-sided adhesive tapes at back.
  3.Paste in car position where the sun can shine.(Important !!!)
 
 
 

 

X (1)X (2)X (3)X (4)X (5)X (6)X (7)X (8)X (10)
 
 

 

 

Customer review